VMware NSX 4.X Professional V2 v1.0
Question 1
When collecting support bundles through NSX Manager, which files should be excluded for potentially containing sensitive information?
- A. Core Files
- B. Controller Files
- C. Audit Files
- D. Management Files
Answer : A
Question 2
What can the administrator use to identify overlay segments in an NSX environment if troubleshooting is required?
- A. Geneve ID
- B. VNI ID
- C. Segment ID
- D. VLAN ID
Answer : B
Question 3
How does the Traceflow tool identify issues in a network?
- A. Compares intended network state in the control plane with Tunnel End Point (TEP) keepalives in the data plane.
- B. Compares the management plane configuration states containing control plane traffic and error reporting from transport node agents.
- C. Injects ICMP traffic into the data plane and observes the results in the control plane.
- D. Injects synthetic traffic into the data plane and observes the results in the control plane.
Answer : D
Question 4
Where is the insertion point for East-West network introspection?
- A. Tier-0 router
- B. Guest VM vNIC
- C. Partner SVM
- D. Host Physical NIC
Answer : B
Question 5
Which is the only supported mode in NSX Global Manager when using Federation?
- A. Proxy
- B. Policy
- C. Controller
- D. Proton
Answer : B
Question 6
When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?
- A. DR is instantiated and automatically connected with SR.
- B. SR is instantiated and automatically connected with DR.
- C. SR and DR doesn’t need to be connected to provide any stateful services.
- D. SR and DR is instantiated but requires manual connection.
Answer : B
Question 7
An NSX administrator is creating a Tier-1 Gateway configured in Active-Standby High Availability Mode. In the event of node failure, the failover policy should not allow the original failed node to become the Active node upon recovery.
Which failover policy meets this requirement?
- A. Enable Preemptive
- B. Non-Preemptive
- C. Preemptive
- D. Disable Preemptive
Answer : B
Question 8
Which CLI command is used for packet capture on the ESXi Node?
- A. tcpdump
- B. set capture
- C. pktcap-uw
- D. debug
Answer : C
Question 9
Which command on ESXi is used to verify the Local Control Plane connectivity with Central Control Plane?
- A. esxcli network ip connection list | grep netcpa
- B. esxcli network ip connection list | grep ccpd
- C. esxcli network ip connection list | grep 1234
- D. esxcli network ip connection list | grep 1235
Answer : A
Question 10
Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)
- A. Must have only active-active edge nodes
- B. Can contain multiple types of edge nodes (VM or bare metal)
- C. Must contain only one type of edge nodes (VM or bare metal)
- D. Can have a maximum of 10 edge nodes
- E. Can have a maximum of 8 edge nodes
Answer : BE
Question 11
An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fail. The administrator knows the maximum transmission unit size on the physical switch is 1600.
Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?
- A. vmkping ++netstack=geneve -d -s 1572 <destination IP address>
- B. vmkping ++netstack=vxlan -d -s 1572 <destination IP address>
- C. esxcli network diag ping –H <destination IP address>
- D. esxcli network diag ping -I vmk0 -H <destination IP address>
Answer : A
Question 12
An NSX administrator is creating a NAT rule on a Tier-0 Gateway configured in active-standby high availability mode.
Which two NAT rule types are supported for this configuration? (Choose two.)
- A. Port NAT
- B. 1:1 NAT
- C. Destination NAT
- D. Reflexive NAT
- E. Source NAT
Answer : C
Question 13
When deploying an NSX Edge Transport Node, what two valid IP address assignment options should be specified for the TEP IP addresses? (Choose two.)
- A. Use an IP Pool
- B. Use RADIUS
- C. Use a Static IP List
- D. Use BootP
- E. Use a DHCP Server
Answer : AE
Question 14
DRAG DROP -
Match the NSX Intelligence recommendations with their correct purpose.
Answer : 
Question 15
Which two built-in VMware tools will help identify the cause of packet loss on VLAN Segments? (Choose two.)
- A. Flow Monitoring
- B. Traceflow
- C. Live Flow
- D. Packet Capture
- E. Activity Monitoring
Answer : BD